Bullet-type 7" high/low beam headlights.

Standard type headlights are of sealed beam lamp deisgn.

All King Bee lights are H4 halogen bulbs.

All headlights sold in pairs only.

Cast aluminum posts are grooved to accept A1023 conduit for wiring. Fits all "Ts" or any fenderless chassis.

Designed to fit most manufacturers' shock brackets for clean installations for all aftermarket headlights.

Must be used with King Bee-style headlights when using A1021 posts.

Polished stainless steel dropped headlight bars. Also available are dropped headlight bars to fit Model A fenders with Deuce grill shells, please call. Limited Availability.

Stamped-steel headlight mounts for use with 1932-style grill shell, stock or chopped. Mounts the headlight to the sides of the radiator. NOTE: Jeadlights need to be modified so that high beam works properly when mounted sideways.

Highly polished stainless steel conduit. Covers horn and headlight wiring on all model As. Stainless steel tubing pre-formed to fit A1021 post.

Enhance the looks of your ride with these chrome bullet style halogen lights. Measure 1 3/8" diameter X 2 7/8" long. Available in both smooth and raised flame designs with amber lenses. Includes mounting studs for easy installation. Function as turn signal only.

Sold in pairs

Single and dual filament turn signal lights feature amber lenses with chrome housings.

Single filament bulb measures 1 3/4"

Dual filament light measures 2 1/2"

Contains 2 TOTAL PERFORMANCE hand-spun lamps along with brackets to install on T Bucket bodies. Brass or chrome. Amber lenses standard.

Contains two TOTAL PERFORMANCE hand-spun lamps along with all the hardware to install on T Buckets with 14" beds. Brackets bolt to the chassis. Brass/chrome. Blue dot lenses optional. For red lens with blue dot add $18.00.

Add that classic look to your "T" with lantern-style lighting. Lenses sold separately.

Convert your TOTAL PERFORMANCE carriage lights with our new LED conversion kit. Brake, taillight, and signal are built into these conversion kits.

The long brackets A269 are used to hold the lamp and a license-plate frame. The steel bracket is used for chassis mounting. If you have a pick-up bed longer than 14" you will not be able to use the steel brackets.

Made from cast aluminum.

This Iron Cross light functions as both a parking light and brake light. L.E.D. lighting makes sure you'll be seen!

The beautiful chrome housing with flat surface and simple mouting allows for easy installation.

This awesome light measures approximately 4-1/2" x 5" x 3/4" thick so it can easily find a home in almost any custom application.

Sold each

These beautiful 4-1/4" diameter taillights are just the ticket for your Hot Rod! Features include a glass lens, chrome bezel and rubber gasket.

Accepts the 1157 style bulb.

Sold as each.

Complete taillamp assembly with very bright and visible LEDs for the stop, tail, and turn signal functions. LEDs feature a wide viewing angle of 100 degrees as well as cool operation and long life. This lamp is designed to bolt into a 1938-39 Ford fender in place of the original taillight. Surface mount design with no bucket. Great solution for cars with clearance problems (rumble seat or tire) or for new installations. Requires drilling only three small holes in new installations. May be used with three or four wire connection (ground, taillight, stoplight, turnsignal).

A507LED (shown) - Sold as each.

A507LED-RF - Includes RapidFire feature, which pulsates the lights rapidly three times before holding them on, each time the brake pedal is pressed. Sold as pair.

Convert original taillights to superbright Halogen. For use with 1939 teardrop lights only.

Replacement Lenses for 1939 Ford Tear-Drop Style Taillights. Rock-A-Billy Style ~El Diablo~ Design. Sold As Lenses Only, Taillights Available Seperately.

Universal in design, these glass blue dots fit most taillights to give them a unique "purple glow." The chrome plated bezel has four retaining tabs for positive attachement and only a 15/16" hole is required for installation. Packaged 2 per set. NOTE: This product is intended for off-road use only and may not be legal for street use in some states.

Original-style chrome reproduction taillights for Model A and '32 Fords.

Note: Left side taillights have window in bottom for license plate illumination. Ride side taillights do not.

Original-style reproduction brackets for 1928 - 1932 street rods.

These LED taillights come in a variety of configurations, from as little as 3/4" wide up to 2" wide. All lights feature brake, taillight, and turn-signal options.

Satin Billet Aluminum Third Brake Light. Adjustable Pedestal Mounting Base.

Measures 7" X 1 3/4" Overall height Including 3/4" Lens Height.

This taillight has a smooth design with billet aluminum trim and molded lens. Mounts easily with hidden fasteners. Each light measures 7-1/2" long x 1-1/2" high x 3" wide.

Add that clean hi-tech look to any hot rod. Mounts flush with the body. We suggest using two pairs of PST111A for efficient illumination.

Available in 1/8", 5/16", and 1/2" green, amber, red, or blue styles. Simply drill proper size hole and push light into place. Small ears on light housing hold it into place. Pre-wired for a simple installation.

A rectangular shaped red high-beam indicator betwen two green rectangular shaped turn signal indicators mounted in a 1/16" thick aluminum plate makes a neat, clean-looking combination. The entire unit measures only 5/8" high x 1-7/8" wide. Long-life LEDs mean no bulbs to change. Easily installed with 24" leads and instructions included. 12v.

Rear license-plate mount and light.

Hide your license plate neatly under your car! Solve your license plate location problems with this vacuum operated license plate holder that automatically lowers when the engine is started and retracts when shut off. This kit requires only a very small amount of vacuum. Comes complete with all installation pieces including an electric switch to defeat the vacuum operation, keeping plate in the up position for parades, etc. A Slick Kit for any street rod, car or truck. Can also be used with blowers and turbochargers!

Machined from 6061-T6 aluminum and cut to a low profile contour, these beautifully polished frames are available lighted or plan. Mounting hardware is included.

Part number 7006 - Lighted frame shown to left.