Made of 305 stainless steel, these clamps securely hold brake lines, wiring, gas lines, or cables. Includes stainless steel button head screws.

Polished aluminum "T" fitting drilled for 5/16" mounting bolt and 1/8" NPT fittings on 3 sides. Perfect for pressure style brake light switch. Decorative ball milled lines on highly polished billet aluminum for added detail.

High quality brake light switches provide much longer life than previous models available anywhere. Both units use 1/8" NPT thread.

Low Pressure unit operates at 20-50 pounds of pressure.

Standard unit operates at 60-120 pounds of pressure

Standard unit used on Total Performance cars with disc/drum brake combination.

New tight fit master cylinder fittings are designed for limited space issue problems. Will work on any GM or Ford master cylinder with 1/2-20 and 9/16-18 thread sizes. Great for additional clearance to crossmembers, transmissions and exhaust systems. These straight thread, 90 degree fittings only require the O-Ring washer to orientate the -4 AN fitting into the angle alignment desired.

Master cylinder fittings available to adapt 9/16-18 and 1/2-20 thread sizes to 1/8 NPT fittings for use with either -3 or -4 AN lines. O-Ring seal prevents leaks. Designed with 1/8 NPT fitting hole size allowing the use of straight or angled AN fittings for all custom applications.

All TOTAL PERFORMANCE brake line kits are 100&per; complete. Includes all necessary fittings, brackets, brake light switch, braided stainless front and rear flex hose, pre-bent and labeled with instructions. For Total Performance vehicles only. Pro Street Kit also includes proportioning valve.

Front brake lines and fitting kit, available in 3/16" and 1/4". Includes all the proper fittings. 22" long.
GM calipers may differ from the 7/16"-24 fitting we provide. Please check threads before ordering.

Braided stainless steel flex hoses for all brake line applications. Available in both 3/16" (3AN) and 1/4" (4AN) sizes and with either straight or angled ends.

This kit is a complete assortment of fittings and brackets along with a stainless steel flex line. Comes complete with chassis mounting and rear end housing mounting brackets.

These brake lines come with double flared ends and AN sleeves and nuts. Priced each.
Special length lines with SAE or AN fittings custom-made to your dimensions or samples. Custom length prices based on $4.00 foot bundy; $5.00 per foot s/s, $1.00 per flare, plus fittings. Polishing $2.00 per foot. Allow 2 weeks delivery.

Machined for 1/8" pipe thread fittings. Mount through frame rail retained by a AN nut. Inlet is 1/8" NPT while outlet is 3/16" (#3) AN. Available in both 2" and 2 1/2" lengths. #3 (3/16") AN lines only.

Bulkheads fittings designed for use with either our steel, weld on tabs (F10310-SP) or our aluminum bolt-on brackets(3600103 or 3600104). Provides a clean appearance to the brake line routing. Available in straight, 90 degree and "T" styles for both #3 (3/16") and #4 (1/4") AN line sizes.

Female tube nuts and sleeves for 3/16" and 1/4" lines.

AN #3 for 3/16" lines

AN #4 for 1/4" lines

Blue anodized aluminum adapters are available in straight, 90 degree and 45 degree styles. Adapts 1/8" NPT fitting sizes to #3 (3/16") or #4 (1/4") AN line sizes.

Straight fittings for adapting either AN #3 or AN#4 to standard inverted flair applications.

A must when flaring brake lines! 3/16" and 1/4" available in steel or stainless steel. Sizes available for all popular applications. Check sizing before ordering.

Tip: Most master cylinders use 9/16" threads.

These fittings are available in either 3/16" (3AN) or 1/4" (4AN) sizes. Ideal for plumbing around tight areas or to extend exsisting brake lines.

SAE style brass fittings- Economical and easy to install. Available for both 3/16" and 1/4" SAE lines. Part number 7812 includes mounting bracket for a solid installation on frames and rear housings.

2-piece line clamps isolate and secure fuel, brake, and wiring runs. Interlocking feature prevents twisting and failure due to flexing vibrations.

Eliminate chafing. Closed or open style. Sold in sets of six.

Designed for all bulkhead style fittings. "L" shaped steel brackets with 7/16" hole. May be welded or bolted for installation.